Loading... Please wait...

fb-findusonfacebook-100.png

Our Newsletter


Suppliers

2co-vertical.png

Adafruit NeoPixel Digital RGB LED Weatherproof Strip 30 LED -1m

  • Image 1
  • Image 2
Price:
$12.95
SKU:
ADA-1460
Current Stock:
13
Quantity:


Product Description

ADVERTENCIA: LOS NEOPIXELES NO VIENEN LISTOS PARA CONECTAR.  FAVOR REVISAR ESTA GUIA ANTES DE CONECTAR:

https://learn.adafruit.com/adafruit-neopixel-uberguide/best-practices

HAY QUE TENER UNA RESISTENCIA ENTRE 300 ohmios y 500 ohmios ENTRE LA LINEA DE DATOS Y EL "DATA IN" DEL STRIP.

HAY QUE TENER UN CAPACITOR DE 1000uF o más grande entre 5V y GND.

These NeoPixel strips have 30 digitally-addressable pixel LEDs per meter and are very affordable and are only 12.5 mm wide, 10 mm if you remove the strip from the casing. This is the strip with black flex PCB.

There are some things to watch for:
These LED's use about 9.5 Watts max (~2 Amps @ 5V) per meter. The max rating is assuming all the LEDs are on full white, usually the actual current for colorful design is about 1/3 to 1/2 the max current.

To make the strip thin and easier to manufacture, the controller chip is inside the LED, which is kind of cool, but also means that the chip only uses a single pin for input and a single pin for output. The protocol used is very very timing-specific and can only be controlled by microcontrollers with highly repeatable 100nS timing precision. We have example code for using with the Arduino Uno/Mega microcontroller at 8MHz and 16MHz, but it will not work with the Raspberry Pi, Basic Stamp, NETduino, any other interpreted/virtual machine microprocessor or any processor slower than 8 MHz. 

The way the pixels are controlled by an Arduino, the entire strip must be buffered in memory, and we've found many Arduino UNO projects only have about a 1500bytes of RAM available after all the extras are included - enough for about 500 LED pixels. If you want to drive the entire strip and have some other libraries included, you may need to use a Mega.


There are 30 RGB LEDs per meter, and you can control each LED individually! Yes, that's right, this is the digitally-addressable type of LED strip. You can set the color of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you

The strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters, there are cut-lines every 1.3"/3.4cm (1 LED each). Solder to the 0.1" copper pads and you're good to go. Of course, you can also connect strips together to make them longer, just watch how much current you need! We have a 5V/2A supply that should be able to drive 1 meter and a 5V/10A supply that can drive up to 10 meters (depending on use) You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip.

Adafruit's detailed NeoPixel Uberguide has everything you need to use NeoPixels in any shape and size. Including ready-to-go library & example code for the Arduino UNO/Duemilanove/Diecimila, Flora/Micro/Leonardo, Trinket/Gemma, Arduino Due & Arduino Mega/ADK (all versions).

Note that these strips are sold in cut segments of 1m.  They may or may not come with connectors.  Assume they don't come with a connector.


Find Similar Products by Category


Add to Wish List

Click the button below to add the Adafruit NeoPixel Digital RGB LED Weatherproof Strip 30 LED -1m to your wish list.

You Recently Viewed...